Установкa Thermo King Super NWD 5300 схема CRANKCASE GROUP (C201) – 3B1
Обновление от: 9/11/09
| № | TK # | Описание | Кол-во Цена | |
|---|---|---|---|---|
| 810-1205 | ENGINE (remanufactured, see note 1) | 1 | ||
| 1 | 101-222 | BLOCK - cylinder | 1 | |
| 2 | 11-2755 | CAP - sealing (32 mm dia) | 2 | |
|
10-10-275 | Заглушки блока, к-т, Isuzu 2.2 | 1 020 ₽ |
|
|
10-10-276 | Заглушки ГБЦ, к-т, Isuzu 2.2 | 1 020 ₽ |
|
| 3 | 55-3529 | PIN - cylinder body to oil base | 2 | |
| 4 | 11-3821 | PLATE - front | 1 | |
| 5 | 55-2409 | PIN - front plate | 2 | |
| 6 | 33-1058 | GASKET - front plate | 1 | |
|
10-33-1058 | Прокладка передней крышки, Isuzu C-201 | 1 000 ₽ |
|
| 7 | 55-1920 | PLUG - tappet chamber | 2 | |
| 11-3369 | CAP - sealing (tappet chamber) | 2 | ||
|
|
10-10-275 | Заглушки блока, к-т, Isuzu 2.2 | 1 020 ₽ |
|
|
|
10-10-276 | Заглушки ГБЦ, к-т, Isuzu 2.2 | 1 020 ₽ |
|
| 8 | 11-3387 | DUCT - water | 1 | |
| 9 | 55-2411 | BOLT - bearing cap | 10 | |
| 10 | 11-3845 | BEARING SET - camshaft | 1 | |
|
10-11-3845 | Вкладыши распредвала к-т, Std., Isuzu C-201 | 2 150 ₽ |
|
| 11 | 30-197 | KIT - crankshaft | 1 | |
|
10-30-197 | Втулка и сальник, задний, Isuzu C-201 Late Block | 7 300 ₽ |
|
| 33-2535 | SEAL - only | 1 | ||
|
10-33-2535 | Сальник коленвала, задний, Isuzu C-201 | 2 850 ₽ |
|
| 12 | 11-3392 | SPACER - oil seal | 1 | |
| 13 | 11-2819 | CAP - sealing (38 mm dia) | 1 | |
| 14 | 11-3370 | CAP - sealing (12 mm dia) | 1 | |
|
|
10-10-276 | Заглушки ГБЦ, к-т, Isuzu 2.2 | 1 020 ₽ |
|
|
|
10-10-275 | Заглушки блока, к-т, Isuzu 2.2 | 1 020 ₽ |
|
| 15 | 11-2757 | PLUG - frost (45 mm dia, see note 2) | 3 | |
|
|
10-10-275 | Заглушки блока, к-т, Isuzu 2.2 | 1 020 ₽ |
|
|
|
10-10-276 | Заглушки ГБЦ, к-т, Isuzu 2.2 | 1 020 ₽ |
|
| 11-5954 | CAP - sealing (46 mm dia, see note 2) | 3 | ||
| 16 | 55-4144 | PLUG - cylinder body | 1 | |
| 17 | 55-2408 | BOLT - front plate | 3 | |
| 18 | 55-2407 | PLUG - oil gallery | 2 | |
| 19 | 55-1967 | PLUG - oil gallery | 2 | |
| 20 | 11-3083 | NIPPLE - injection pump oil feed | 1 | |
| 21 | 55-5461 | PLUG - oil gallery | 1 | |
| 22 | 33-653 | GASKET - plug | 1 | |
| 23 | 11-3380 | COVER - tappet | 1 | |
| 24 | 33-783 | GASKET - cover | 1 | |
|
10-33-783 | Прокладка крышки толкателей, Isuzu C-201 | 530 ₽ |
|
| 25 | NSS | BAFFLE - cover | 1 | |
| 26 | 55-2401 | RIVET | 6 | |
| 27 | 55-2408 | BOLT - cover | 14 | |
| 28 | 33-659 | GASKET - breather | 1 | |
| 29 | 33-784 | GASKET - breather | 1 | |
| 30 | 11-5326 | BREATHER | 1 | |
| 31 | 55-1935 | BOLT - breather | 1 | |
| 32 | 55-2069 | CLAMP - hose | 2 | |
| 33 | 11-2943 | HOSE - breather (before S/N 540022) | 1 | |
| 11-5521 | HOSE - breather (S/N 540022 & after) | 1 | ||
| 34 | 11-3383 | PLUG - plate | 1 | |
| 35 | 55-2412 | NIPPLE - rocker oil feed | 1 | |
| 36 | 11-3384 | PLATE - rear | 1 | |
| 37 | 55-2023 | SCREW - plate | 3 | |
| 55-3528 | BOLT - reamer (11 mm dia) | 1 | ||
| 55-4187 | BOLT - reamer (replacement, 0.498 dia) | 1 | ||
| 55-6370 | BOLT - reamer (replacement, 0.560 dia) | 1 | ||
| 55-852 | NUT - reamer | 1 | ||
| 38 | 55-2094 | PIN - dowel (standard) | 1 | |
| 55-4009 | PIN - dowel (1st oversize) | 1 | ||
| 55-6362 | PIN - dowel (2nd oversize) | 1 | ||
| 39 | 11-3385 | CAP - sealing (36 mm) | 1 | |
|
|
10-10-275 | Заглушки блока, к-т, Isuzu 2.2 | 1 020 ₽ |
|
|
|
10-10-276 | Заглушки ГБЦ, к-т, Isuzu 2.2 | 1 020 ₽ |
|
| 40 | 55-2405 | PIN - dowel (cylinder head) | 2 | |
| 41 | 11-7043 | SLEEVE - repair | A/R | |
|
10-11-7043 | Гильза, Isuzu C-201 | 8 730 ₽ |
|
| 810-269 | KIT - engine overhaul | 1 | ||
| 10-258 | PLUG - freeze, block (incl 2, 13, 14, 15, 18, 34, 39) | 1 | ||
|
10-10-258 | Пробки блока к-т, Isuzu C-201 | 2 770 ₽ |
|
| 42 | 40-224 | KIT - frost plug heater | 1 | |
| 43 | 40-522 | KIT - low speed start | 1 | |
| 44 | 204-480 | INSTALLER - camshaft bearing | 1 | |
| 30-175 | GASKET SET - engine overhaul | 1 | ||
|
10-30-175 | Набор прокладок двигателя (вкл. маслосъемные колпачки), Isuzu C-201 | 18 100 ₽ |
|